Back to the discussion

in Thèmes › Voyager en camping-car

Converting a heavy-duty bus/coach/truck into a motorhome (page 127 of 161)

Discussion started by Patrick26 on 2004-06-14

3213 replies

This thread has been translated into English.


Converting a heavy-duty camper van in a bus/coach/truck

Gwennn · 2007-03-06 · Message 2521 of 3214

Hey everyone! 😉

Okay, the truck purchase is getting closer, so I wanted to know if the conversion standards for a bus are the same as for a truck. I’m not sure I can follow everything to the letter, but just enough to avoid any issues when it comes to the inspection. So I’ll smooth out the rough edges, remove my stove every two years, but apart from that, I don’t see what they could fault me for. If you’ve got a couple of tips, that’d be great.

Take care and safe travels! Cheers

Converting a heavy-duty truck into a motorhome using a bus/coach/truck

Dge23 · 2007-03-06 · Message 2522 of 3214

Yes, the layout standards for HGVs and buses are the same since a bus is itself a heavy goods vehicle once it’s been reclassified as a motorhome.

Converting a heavy-duty camper into a bus/coach/truck

Gasmobil · 2007-03-06 · Message 2523 of 3214

For a fully eco-friendly engine, I don’t know of any solution. However, there are possible adaptations with GVI and the Pantone reactor. GVI (Générateur de Vapeur Instantané) is a system installed in the exhaust that recovers lost heat from combustion to instantly produce steam, as its name suggests. This low-temperature, humid steam then feeds a Pantone reactor.

The Pantone reactor, also installed in the exhaust, recovers lost heat from combustion and transforms a mixture of humid steam and air into a kind of LPG that’s reinjected into the engine’s intake.

Pollution reduction is almost immediate. Black smoke disappears completely, there’s a power gain, and around a 40% fuel consumption reduction depending on the setup. The cost of use is just... water!!!

Check out two non-exhaustive experiments at these addresses: http://reaction.directe1.free.fr/Merco220D/merco.htm Top-notch setup on a Mercedes http://reaction.directe1.free.fr/205D/205D.html Top-notch setup on a Peugeot 205 http://reaction.directe1.free.fr/index.htm http://www.econologie.com/articles.php?pg=70 Top-notch setup on a Citroën ZX

I haven’t found any tests on buses, but there are some on tractors: http://quanthomme.free.fr/pantone/FrancePMC.htm On this page, dozens of working tests sorted by modification year and vehicle type: lawnmowers, cars, excavators, tractors, generators, etc.

In my opinion as a technician, the GVI system is the most suitable for buses.

The method used on tractors and generators, for example, has a certain inertia. The system uses a bubbler (a tank of water heated by the exhaust) to produce steam. Given the water volume—even if small—there’s a delay in reaction time. When you accelerate, it takes time to heat the water enough to meet the engine’s demand. When you decelerate, it takes time for the water to cool and produce less steam, so during that time, it overproduces. So it’s great for engines with a more or less constant speed, like agricultural machinery plowing or generators.

The advantage of GVI is its heat exchanger directly in the exhaust pipe. There’s no water "stock" to heat or let cool. Steam production is almost instantaneous and proportional to the engine speed since it’s linked to the volume and temperature of the exhaust gases. So there’s little reaction time (estimated at around 2 seconds), unlike the method described in the previous paragraph.

Check this address for more precise info on how the reactor works and how to build it: http://quanthomme.free.fr/pantone/PageM_David.htm

In my opinion, this is something to keep an eye on. Patrick already brought it up without getting much reaction. I think it could reconcile our passion with ecology while also offering substantial savings—which doesn’t hurt. The only downside is that it’s about as legal as running on vegetable oil. I’m just saying that, but I have no info on the authorities’ stance on this. I just assume they’re not thrilled.

Best regards, I’m looking forward to your reactions—hopefully many—or at least some effort to learn more about this promising topic.

Converting a heavy motorhome from a bus/coach/truck

Patrick26 · 2007-03-06 · Message 2524 of 3214

And Gwennn, just a reminder that cheating isn't playing fair!

Removing your stove to pass the technical inspection every year (instead of every two years) won't do you any good! At the inspection center, they don't care about your interior setup! For now, anyway... in a few years, that might change!

It's during the Veritas inspector's visit or another certifying body that you'll need a certified cooking appliance! And once it's there, you might as well leave it in place!

Go back and read the post I made 5 or 7 posts above—you'll need to follow those steps to pass the inspection for your certification!

Stop racking your brain trying to figure out how to cheat! Keep it simple! Follow the regulations, and everything will go smoothly...

PATRICK26

Converting a heavy-duty camper van from a bus/coach/truck

Gwennn · 2007-03-06 · Message 2525 of 3214

It's not about cheating or not—otherwise I'd be driving without a license, without an inspection, and without an address, come what may... It's just that I hate having to buy another stove when I already have a brand-new one. But a regular one

Converting a heavy-duty camper into a bus/coach/truck

Hotware · 2007-03-06 · Message 2526 of 3214

Here we go again with this old chestnut, our friend the "Pantone engine." Okay, to keep it short (I’ve already repeated this 10,000 times, and I’m getting tired), the Pantone is like those fuel-saving magnets—might as well carry a rabbit’s foot. So, in summary: We still have the same few folks raving about the wonders of their contraption. Every time, the tests are subjective, or there’s a test, but it’s on smoke opacity (inject water into your exhaust, and you’ll get the same result: you condense your smoke. The pollution doesn’t change, but it’s not measured by the technical inspection device…). "It works great on my generator, here’s a video": sure, but the generator’s running idle, never under load. Odd, right? They’ve never responded to the few serious eco sites that offered 10,000 € to anyone who could demonstrate an effective Pantone, meaning tests on a dynamometer. A number of people have tested it without conclusive results. Water doping was used when engines were less efficient, especially in aircraft. Since then, engine efficiency has improved, and we’ve replaced that kind of thing with a turbo. But I’m open to anyone who wants to test this engine on a dynamometer. The only gain comes from slower acceleration—achieving the same thing just requires a light foot. Since combustion isn’t complete with a Pantone, the pollution emitted (unburned fuel, carbon monoxide) must be significantly higher. Finally, given the "miracles" the Pantone supposedly performs (50% less fuel consumption…), I’m waiting to see who’ll take their 20L/100km camper down to 10L/100km ;)

Converting a heavy-duty camper into a bus/coach/truck

Dge23 · 2007-03-06 · Message 2527 of 3214

I’ve got a brand-new wood-burning insert, so why bother installing a gas heater up to code? 😊 But maybe for safety’s sake it’s worth trying to follow the standards, especially when it comes to gas in case something goes wrong.

Converting a heavy-duty bus/coach/truck into a motorhome: minimum requirements for certification

DTFsound · 2007-03-06 · Message 2528 of 3214

What are the minimum modifications needed to get a motorhome certification in the end? Are gas or heating systems part of the required changes for certification?

Converting a heavy-duty camper from a bus/coach/truck

Isaraph · 2007-03-06 · Message 2529 of 3214

Thanks for the links to other sites—there are loads of school buses, not as nice as the Flexible, but still cool. It’s not gonna be easy, though. As for our 2.0L TDCI engine, we’ve already sorted the CO₂ emissions for the buyback. The solar panels are done too. All that’s left is to upgrade the engine—there’s a German university working on cleaner engines, so I’m still looking for the best fit, especially since our heating runs on diesel. But I haven’t given up on finding an old bus with character to convert. 😕

Converting a heavy-duty camper from a bus/coach/truck

Patrick26 · 2007-03-06 · Message 2530 of 3214

You know, my bus was a school bus—yellow with brown lower panels, just like back home, and the only model made in Europe, by the way!

Given all the transformations it’s undergone today, I just had to say it so people know!

Check out my blog for its full history!

PATRICK26

Converting a heavy-duty camper van from a bus/coach/truck

Patrick26 · 2007-03-06 · Message 2531 of 3214

You grab the AFNOR book on converting a camper van, standards 56-200 and 56-201, and you’ve got everything you need to comply! It’s simple!

You can order the book online from AFNOR, and the two standards can be downloaded from my blog (under the "normes" section).

If you want to modify the seating layout or add seats, you can refer to the seat and seatbelt standard, also on my blog under the "sièges" section.

The blog address is at the bottom of my posts!

See, it’s really simple—just a matter of knowing how to read. My 12-year-old kid, who’s passionate about the project, discusses certain points with me ("Dad, the pipe for the gas exhaust, given its length, should be about 8 to 9 cm in diameter, right?" – "Yes, that’s right, since it’ll be between 80 and 90 cm long to cross the storage compartment.")

It’s already complicated enough trying to do things properly—don’t try to cut corners just to fail the homologation inspection after investing your time and savings! That’d be such a shame!

And if you don’t have the budget, work, save, or take out a loan! Some things have non-negotiable costs!

You don’t build a house with 20,000 €, you don’t buy a pack of cigarettes with 1 €, and you don’t convert a bus into a camper van with 5,000 €!

I know, it’s tough, but you’ve got to be realistic! I dreamed about it for 8 years before buying the bus! Today, it’s almost finished—just a few bits left (a Webasto T2400 or T3000, a heat-exchanger water heater, two tanks, a Studer C2200-24, and a couple of other small things), all for 4,000 €... and that’ll have to wait a bit! My health issues have cut my income by two-thirds for the past 7 months, and that’s taken a toll on my savings. Had to make a choice: feed myself and my kids or finish the bus! 10 years of dreaming! We’ll wait a little longer...

The worst part is I *could* change my plans, simplify things... but no! I’d rather wait a bit longer and have what I’ve dreamed of for so long! I want it to be Christmas one day—finally! But for that, you’ve got to be patient, patient...

All this to say (for you, gwennn) that it’s no big deal if you already have a gas stove—sell it! And buy a proper, certified one! You’ll see, you’ll be happy and proud, not to mention peace of mind!

And for everyone else, the mental journey you’ve got to make is the same as gwennn’s... It’s not a big deal, not mean—it’s just the impatience of youth! The only problem is it leads to mistakes... So there are (already!) old fools (I’m 39!) trying to show you the way and spare you the hassle!

After that, everyone does as they please, but they own it! I’m giving advice here and now—don’t come crying to me after failing the inspection asking how to fix your mistakes. Because you already know the answer! You dismantle and start over!

And if it’s after an accident, the only advice I can give right now is: "Find a good lawyer!"

But don’t get discouraged either! I remember Athenol who finished his project! Not a huge budget, he worked like crazy during the week and slaved away on his bus every weekend! 6 to 8 months of work total! Bravo! At 25 or 27 years old, hats off!

I get that some people wish it were simpler, but in France, nothing’s simple! On the other hand, we’ve got schools for our kids, hospitals when we’re sick, unemployment benefits when we’re out of work, and pensions when we’re old! There are countries where it’s easier to convert a vehicle! Where you don’t have to go through inspections—in those countries, the only "mines" you’ll find, you’ll often step on them! It’s up to you to choose! To me, the inspection requirements for homologating my vehicle seem minor compared to the advantages of living here! I’ve made my choice—I’m staying! I take the perks (I just had surgery that must’ve cost the healthcare system several hundred thousand euros) and I put up with the hassles (the inspection requirements for homologating my truck).

Even the best ribeye steak has fat around it!

PATRICK26

Converting a heavy-duty camper into a bus/coach/truck

Toma29 · 2007-03-06 · Message 2532 of 3214

Nice reflection, it all feels poetic and full of beautiful words. You can tell you’ve lived it. I agree that at 20, you’re young, but at 39, you’re not old. Stupidity and ignorance have no age.

I’ll take this opportunity to make a call. I’m looking for a bus in Brittany, still in TCP status or downgraded to heavy-duty vehicle, anywhere in France. Preferably empty and with a budget of 15,000 € max. Thanks, and good luck to those who’ve already started converting a bus!

Converting a heavy-duty camper van from a bus/coach/truck

DTFsound · 2007-03-06 · Message 2533 of 3214

Every time I ask you a question that just needs a general answer, oh wise one, you send me to a 45 € book or your blog with legal texts so complex that only a lawyer could find their way through. The young, pressed idiot that I am (35 years old) thought this forum was for sharing tips to make life easier when dealing with procedures and understanding regulations. Oh well, I was wrong.

So enough with the nonsense, we’ll load up the bus on the sly and hit the road like that—FUCK THE SYSTEM.

Good luck to everyone, and see you at the rave!

Converting a heavy-duty motorhome from a bus/coach/truck

Tortue26 · 2007-03-06 · Message 2534 of 3214

hi everyone, just a quick mechanical/technical question. After starting the coach to let it run a bit and do 2 or 3 maneuvers, I suddenly lost the clutch. I took a look—it seems to be a hydraulic clutch. So if anyone could tell me what fluid to use to fix it, and confirm that’s really the issue, that’d be great. And finally, to wrap up: it lifted just fine, no problem, but after turning off the engine, it didn’t come all the way back down—the rear left side stayed up. If anyone can explain why that happened, I’d really appreciate it! Thanks

Converting a heavy-duty camper van from a bus/coach/truck

Gwennn · 2007-03-07 · Message 2535 of 3214

hi well, I’ve got a wood stove, so for heating I’m not planning to add anything else, but for the gas stove, I’m not sure if I can use mine with a bottle. but it’s clear you’ve gotta be careful—if it means risking not being able to drive anymore, it’s not worth it... cheers

Converting a heavy-duty camper van from a bus/coach/truck

SJunior · 2007-03-07 · Message 2536 of 3214

Hey everyone!

It’s been a while since I last posted, but I really wanted to chime in here...

Let’s all take a deep breath for a sec! This thread was created to share info and tips on converting buses/heavy-duty vehicles while respecting regulations!!

I get it—reading through norms and regulations isn’t always fun, but the AFNOR guide isn’t just a dry rulebook. It’s actually pretty clear (with explanations and diagrams). That said, like any rule, the tricky part is how it’s applied. Depending on the *DIRE* (regional transport authority) and the department, you might get different answers. So yeah, there’s some interpretation involved, and everyone ends up with their own "truth." But some points are crystal clear and non-negotiable!

So, for those of you who want to turn your rigs into rolling fire hazards (reminds me of the early squabbles here) with wood stoves and non-compliant gas cookers—this isn’t just about safety vs. regulations! The "fear of the cop" shouldn’t be your motivation. Cut costs if you want, take the risk of losing *everything* if your truck goes up in flames—your call. But here’s the catch: it’s not just *your* problem. It affects other road users and the people you’ll be carting around in your clunker—your kids, friends, etc. If you’re doing this to save a few hundred euros, I don’t think it’s worth the risk! This isn’t about being open-minded; it’s about responsibility! If you’re diving into these projects with no budget, trying to convert "on the cheap," bit by bit, you’re making compromises that shouldn’t even cross your mind. If something goes wrong (and I really hope it doesn’t), what are you gonna say? "I get it, Your Honor, but I had a brand-new gas stove, so..." (I’m using this example, but I’m not calling anyone out specifically!)

Otherwise—and I hate to repeat myself—there’s no one-size-fits-all answer! There’s no "minimum build" for homologation (except that any empty space can be considered a cargo area, which triggers specific requirements). If you’re asking these kinds of questions, you’re probably approaching the project wrong. You’re not converting a vehicle *just* to get it approved—you’re doing it to live in it! And every use case demands different setups, which means different parts of the regulations apply. To simplify: If I’m traveling solo, in summer, for 15 days a year, in a hot country, and I only eat out, my build (and the norms I need to follow) won’t be the same as a family of five hitting the road every school holiday and every weekend, fully self-sufficient, etc. So stop asking broad questions that can’t be answered—be specific, clear, and detailed!

These projects take financial resources, patience, and time. Take the time to write readable posts (in proper French, no abbreviations) and don’t hesitate to go into detail!

Ask yourselves these questions, both for how you’ll *use* the finished camper and for the entire "construction" phase (buying and converting): Who, When, What, Where, and How

Anyway, happy building!

Converting a bus/coach into a heavy-duty motorhome

Tetell · 2007-03-07 · Message 2537 of 3214

Wow, it's intense here! I’m Christelle—full-time mom to 4 kids, part-time at 7, and 3 Cane Corsos—oh, and a husband 😜. With this whole crew, we decided to convert a 1981 S 53 DE bus (for precision’s sake). So, we bought the AFNOR guide and the bus itself, but where do you get equipment like a stove or fridge… and preferably *without* breaking the bank? Please don’t roast me on my first post!

Outfitting a heavy-duty camper in a bus/coach/truck

Gwennn · 2007-03-07 · Message 2538 of 3214

hi, for accessories, Mrkonn talks about them a bit on page 104, and I think someone shared a few links not long ago too. otherwise, on eBay there’s a guy selling lots of accessories for caravans and motorhomes at pretty good prices—he’s got a shop in Merlevenez (56). some great deals there... the seller’s username is "access560" happy hunting and safe travels! cheers

Converting a heavy-duty camper van from a bus/coach/truck

Gasmobil · 2007-03-07 · Message 2539 of 3214

Hi there and welcome!

For equipment, you might find some great tips on Ebay—just make sure it meets the standards for your intended use. Otherwise, there are sites like Narbonne Accessoires, Top Accessoires, etc.

Best regards.

Converting a heavy-duty camper from a bus/coach/truck

07jack · 2007-03-07 · Message 2540 of 3214

hi there, glad to see I’m not the only one going a bit crazy. I need to buy a smaller bus than yours—just 30 seats. I’ve been told I have to put it on a flatbed (remove the rear seats), take it to the inspection center like that, and then convert it afterward. What do you think of this approach? also, my insurer only covers passenger vehicles. Do you know of an insurance company that could cover me now and once it’s finished? Thanks.

VoyageForum — the largest community of French-speaking travellers.