Back to the discussion

in Thèmes › Voyager en camping-car

Converting a heavy-duty bus/coach/truck into a motorhome (page 128 of 161)

Discussion started by Patrick26 on 2004-06-14

3213 replies

This thread has been translated into English.


Converting a heavy-duty camper van from a bus/coach/truck

Patrick26 · 2007-03-07 · Message 2541 of 3214

My reply wasn't just for you...

But yes, I did answer your question! That famous 45 € book is a must-have! It's like trying to pass your driving test without buying the highway code book!

Me, the old sage (as you put it), and the others on this forum, we’ve already been kind enough to tell you where to find it! We spent nights digging to figure out where to get it!

So this forum *does* meet your expectations by saying:

"I thought this forum was for sharing tips to make life easier when navigating the steps and understanding the regulations."

At least take the time to read them calmly, without rushing, and afterward, if you don’t understand certain points, we’ll be happy to answer...

As for the regulations on my blog, it’s the same!

But know this—something I’ve already said two or three times to those who start with your mindset:

"So enough with the nonsense—just load up the bus haphazardly and hit the road like that, and SCREW THE SYSTEM."

It’s your right, but it’s *your* responsibility! Especially if you have an accident—make sure the idiot opposite you or the injured kid isn’t me or one of mine, because, buddy, you won’t be out of the woods!

Last point, just so you know: what do you live off? Because SCREW THE SYSTEM while living off unemployment or social benefits—I can’t stand that!

It’s either you reject everything outright, or you take the good and accept the constraints! That’s how life works for everything! Those who don’t get that are has-beens (out of the game)!

I don’t wish you anything bad—just that the system you spit on with all your arrogance catches up with you at the first crossroads after you leave! That’ll be one fewer hazard on the roads!

It’s because of guys like you that officials are increasingly reluctant to approve vehicles converted by private individuals! Basically, you’re harming *us*! But given your view of community life, you obviously don’t care!

PATRICK26

Converting a heavy-duty motorhome from a bus/coach/truck

Christobale · 2007-03-07 · Message 2542 of 3214

Tortue26, to properly answer your question, you need to specify the model of your bus. However, there are still some common points for many vehicles. For the clutch, there’s a sender under the pedal that works with a type of Lockheed hydraulic fluid, then a receiver near the engine that takes the fluid and controls the clutch with air. That’s why you should never leave a gear engaged—some vehicles have safety features and won’t start afterward. For the suspension, it’s the same; it uses air because it’s more comfortable for passengers, and you might have an issue with the check valves or a leak. The suspension isn’t too serious, but for the clutch, a sender can cost between 400 € and 1000 € depending on the model. Before getting to that point, check if anything happens when you press the pedal. Normally, you should hear a sharp air noise with every pedal movement... Good luck

Converting a heavy-duty camper van from a bus/coach/truck

Patrick26 · 2007-03-07 · Message 2543 of 3214

welcome!

I suggest we have a phone call tomorrow evening to flesh out your project. Doing it by posts will take forever! I have unlimited calls, so I'll ring you.

Please send me a landline number via private message on this forum (don't post it publicly!) today.

Just click on my username, and at the bottom of the profile, you'll see something like:

Send a private message to PATRICK26

Click on that, and it works just like making a post—except only I can read it!

PATRICK26

Converting a heavy-duty camper into a bus/coach/truck

Patrick26 · 2007-03-07 · Message 2544 of 3214

not necessary!

In the scenario you describe, you’d need to install a load retention partition to protect the driver. And you’d end up with a NON-SPEC VASP!

No point! Park your bus somewhere, do all your conversion work perfectly, and then follow the standard procedure!

A vehicle in the middle of conversion shouldn’t be driven! And if it’s just to take it to the mechanic, ask them to come pick it up and drive it with their garage tow truck—they’re used to it!

For insurance, send me your private email via PM, and I’ll pass along the details of an insurer who takes us on without fuss!

PATRICK26

Converting a heavy-duty camper van from a bus/coach/truck

Mrkonn · 2007-03-07 · Message 2545 of 3214

😉Hi Tetel and everyone,

There are lots of listings online—you just have to dig a little. I also see you're in the 17th; lots of S53 buses are being prepped there. Including Kali’s build: http://merco.aceboard.fr/88678-444-6196-12-commence-transformation.htm—it’s really cool!!!

Converting a heavy-duty camper van from a bus/coach/truck

Jurafreehome · 2007-03-07 · Message 2546 of 3214

Hey everyone, Patrick you nailed it—exactly right! I’m all for anarchy too, but not when it comes to safety and everything that goes with it. So, ravers, if you don’t want to get anything certified and prefer living off-grid, take your vehicle and head to Africa—you’ll see nothing’s certified there, and you’ll find everything to convert it for *really* cheap.

Otherwise, I was wondering if caravan conversions could be adapted for a coach (same standards).

Thanks to all, keep it up, and stay strong!

Converting a heavy-duty camper van from a bus/coach/truck

Tome38 · 2007-03-07 · Message 2547 of 3214

hey everyone

I’m looking for someone in Lower Normandy (department 50) who knows about coaches or a mechanic to go check out a coach. Please drop me a PM if you can help, thanks!

Let’s keep it chill here on the forum🙂

A + 😎

Converting a heavy-duty camper van from a bus/coach/truck

GRD · 2007-03-07 · Message 2548 of 3214

To keep it simple for interior fittings: Wood, coal, oil, and kerosene stoves are BANNED in motorhomes (VASP) or camper vans (CC) due to CARBON MONOXIDE—a deadly, ODORLESS, and COLORLESS gas in enclosed spaces; --for domestic gas stoves, they’re also banned because the burners must be screwed onto the cooktop to prevent movement while traveling; --many DIYers converting vans salvage complete caravan interiors for their layouts.

Just a heads-up—don’t overlook your insurance, which will drop you at the first hiccup and even come after you to recover costs if you’re not up to code.

GRD (retiree who had to abandon the bus project due to a Class C license but makes up for it in a camper van)

Converting a heavy-duty camper into a bus/coach/truck

Jose6440 · 2007-03-07 · Message 2549 of 3214

Wow, that’s quite the bold move! But you’re right to put some people back in their place—those who don’t want to follow the rules will eventually get a taste of their own medicine! So don’t mess around!!! See ya, Jose

Converting a heavy-duty motorhome from a bus/coach/truck

Jose6440 · 2007-03-07 · Message 2550 of 3214

hey tortue26 for the clutch, check the fluid level in the reservoir (it's brake fluid) and check your service bottle fill indicators—if there isn't enough pressure, your clutch pedal will stay stiff. In my opinion, you've just got an air valve that's stuck and the slave cylinder that's deflating must be related. After that, you can check and bleed the clutch system, but I don't think so unless there's an oil leak. I had pretty much the same issue with my FR1 after leaving it parked all winter. Keep us posted and don't hesitate to ask for advice before changing any parts—these things happen when it's been sitting for several days, but it's often nothing major.

take care, jose

Converting a heavy-duty camper van from a bus/coach/truck

Patrick26 · 2007-03-07 · Message 2551 of 3214

Some have tried repurposing a caravan conversion, notably fr159 if I'm not mistaken (at least partially). The big problem is that a caravan is square, whereas the sides of a bus are always curved! So for the furniture, it's a nightmare!

Then, in a caravan, apart from the kitchen (fridge, cooktop, sink), there isn't much technical stuff worth salvaging!

So generally, it costs more to buy a caravan just to strip it down than to source what you really need from an accessories supplier.

Anyway, on this forum, those who've done the research and calculations have all given up or nearly all... Let those who've actually done it give you advice, but apart from fr159 who talks about it on his blog, I don't recall any other forum member who ultimately chose this solution.

PATRICK26

PS: Thanks for your support, José! I don’t want to come off as the bad guy, but you need a bit of realism! You can do a lot with a few ideas and being resourceful, but I don’t know anyone who’s built something from nothing! Apparently, a very long time ago, in 7 days, the world was supposedly created from nothing by a supreme being we still call God today! Apart from Him, I don’t see anyone else, and even then, many doubt the truth of that story, myself included...

Converting a heavy-duty camper van from a bus/coach/truck

Tortue26 · 2007-03-08 · Message 2552 of 3214

Hey Jose, thanks for your reply. I’ll check the level—looks like the tank’s empty. We’ll start by topping up the **AdBlue** and then see about the valves and the bleed. There must be a small leak in the system, and once the vehicle’s off, you can hear air escaping from the front bottle near the diesel tank. For reference, it’s a short Saviem E7—the same one Cateludo has, by the way. After checking, the alternator puts out 50 amps. If anyone can confirm that, it’d be great. Thanks!

Converting a heavy-duty camper into a bus/coach/truck

Tortue26 · 2007-03-08 · Message 2553 of 3214

To answer you, it's a short 1973 Saviem E7, the same as Cateludo’s, and there’s no air noise when I press on it. But I’ll start by filling up with Loukeed and we’ll take it step by step. Thanks

Converting a heavy-duty camper van from a bus/coach/truck

Jurafreehome · 2007-03-08 · Message 2554 of 3214

okay, thanks a lot Patrick! I’ll still do the math though, because I can get a caravan for 300 €, so I’ll see. ciao, have a good afternoon everyone, and good luck to those who are working—I’m heading back.

Converting a heavy-duty camper van from a bus/coach/truck

Jose6440 · 2007-03-08 · Message 2555 of 3214

hey tortue26

After reapplying some Lokid, you need to check your hydraulic circuit—you definitely have a leak or a faulty seal. Once you’ve fixed it, you’ll need to bleed the circuit. See ya, jose

Converting a heavy-duty camper into a bus/coach/truck

Gasmobil · 2007-03-08 · Message 2556 of 3214

Hello everyone. For those who are open-minded and curious, and for the skeptics of the GVI+Pantone Reactor system, here’s an update on the car preparations ahead of the IUT test bench session. link: http://reaction.directe1.free.fr/Merco220D/020307.html

The program includes 45 tests, with and without the Pantone system, at different power levels.

There will be 7 people working on it, plus an eighth handling photos and videos... Eight parameters will be measured (Pin, Pout, T°vap, T°adm, T°GEe, T°GEs, Qeau, Qgo) and seven signals (vibrations for 3 cylinders, inductive sensor, piezoelectric sensor on the first injector tube, vibration sensor on the exhaust pipe outlet, electrodynamic sensor). Three test series: without Pantone, with Pantone, and with simple steam.

For each series, we’ll test three load regimes (braking torque on the bench) at 25%, 50%, and 75% of the engine’s maximum power. Finally, for each load range, data will be collected at stabilized engine speeds of 1000, 1500, 2000, 2500, and 3000 rpm. Fuel consumption will be measured using a 200 g diesel sample each time, with combustion time recorded.

That’s a total of 3 x 3 x 5 = 45 measurement/acquisition points!

We’ll finally see if scientific measurements confirm what some call a "subjective" pipe dream.

At least this is more than just running a lawnmower engine or a generator at idle...

For reference, check out my previous post on this topic—these are vehicle conversions that actually drive, not just coasting downhill!!!

http://quanthomme.free.fr/pantone/FrancePMC.htm

On this page, dozens of successful tests sorted by modification year and vehicle type: lawnmowers, cars, excavators, tractors, generators...

You’ll see it’s not just working in "static" mode—it’s adaptable to bus engines too. 😏

Converting a heavy-duty camper into a bus/coach/truck

Hotware · 2007-03-08 · Message 2557 of 3214

I’m pretty curious to see these tests—post here when they’re out! ;) And with a turbo, the performance must be quite different... Though a lot of bus engines already have one!

Converting a heavy-duty camper into a bus/coach/truck

Benhurd · 2007-03-08 · Message 2558 of 3214

I don’t quite agree with the restrictions mentioned here. When I converted my bus, I asked a lot of questions to the mining authority rep and to Veritas. I have a standard gas stove in my bus. I asked Veritas beforehand if I could do it, and they said yes, provided: - it’s securely fixed - burners over 2500W must have a gas cut-off safety system (a system that cuts the gas if the flame goes out) - the burners aren’t screwed in, but they’re never used while driving (the gas must be turned off) - it passed inspection with the gas stove installed.

For wood, coal, or oil stoves, the room volume standards indicated in the sales docs apply. Portable oil stoves are obviously banned because the minimum standard is around 150 m². Other systems with an external chimney are allowed. Three-quarters of the time, the standards are the same as for a house. Of course, these appliances mustn’t be used while moving. The only heating devices allowed while driving are Webasto and similar brands.

For those worried about carbon monoxide (I’m one of them), you can find alarm detectors on eBay.

A tip for beginners: Everything original is up to standard (even if the standards have changed). All modifications must meet current standards. Example: no seatbelts on original seats, but if seats are replaced, they must respect the manufacturer’s anchoring points and meet current standards (with seatbelts).

Converting a heavy-duty camper into a bus/coach/truck

Kersode · 2007-03-09 · Message 2559 of 3214

Hi there, this weekend I’ll be tinkering with the coach. Could you take a look at the two private messages I left you or the one on your blog? See you soon and thanks in advance

Converting a heavy-duty camper into a bus/coach/truck

Patrick26 · 2007-03-09 · Message 2560 of 3214

BENHURD,

I agree with what you're explaining!

But there's still one problem that needs to be raised...

Even if the mining engineer and the Veritas inspector show some common sense, nothing changes the fact that there are rules set by our assembly, and in case of a problem, no matter how much you say "yes, but...", a judge will stick to the law! Period, end of story!

And the law states that cooking points must have their burner caps screwed on!

The day there's a problem, the mining engineer and the Veritas inspector won't be called to court, not even heard as witnesses! And the "yes, but, Your Honor, it's only used when the vehicle is stationary, that's why I allowed myself to bypass a law that seemed pretty stupid to me" definitely won't make him laugh much!

That's why I, and others, choose to rely on the regulations and not on the personal opinions and considerations of these mining clowns!

Just for comparison, if you want to pay less tax, the best tax advisor is certainly not the tax inspector you depend on! However, if you need a tax clearance, you have to turn to them!

I apply the same reasoning to the mining regulations!

PATRICK26

VoyageForum — the largest community of French-speaking travellers.