Back to the discussion

in Thèmes › Voyager en camping-car

Converting a heavy-duty bus/coach/truck into a motorhome (page 130 of 161)

Discussion started by Patrick26 on 2004-06-14

3213 replies

This thread has been translated into English.


Converting a heavy-duty camper into a bus/coach/truck

Patrick26 · 2007-03-13 · Message 2581 of 3214

In my opinion, you don’t need to on the original seats mounted on the original fixings.

For more details, download the regulations from my blog, under the "seats" section, and make up your own mind. That’ll help you argue your case if there’s an issue or just a question with the mining engineer.

PATRICK26

Converting a heavy-duty camper van from a bus/coach/truck

Kersode · 2007-03-13 · Message 2582 of 3214

hi there, you can reach me either Thursday between 11:00 AM and 12:30 PM or between 6:00 PM and 8:30 PM at the number I sent you in a PM. By the way, do you think it’s possible to cut the roof to install a skylight above the shower—on the left side of the middle door? José, if you know the answer, don’t hesitate! see you soon

Converting a heavy-duty camper into a bus/coach/truck

Fr159 · 2007-03-13 · Message 2583 of 3214

Hi Kersode

OK, I'll try to call you at the times you mentioned. I installed a skylight above the shower and another one above the toilet, so yes, you can put in one or more skylights. But here's a tip: always measure, drill, and cut from the inside to avoid hitting a reinforcement beam.

Converting a heavy-duty camper into a bus/coach/truck

Kersode · 2007-03-13 · Message 2584 of 3214

Thanks for the reply! You used 40 cm skylights, no doubt?

Converting a heavy-duty camper van from a bus/coach/truck

Mrkonn · 2007-03-14 · Message 2585 of 3214

Hey everyone,

Can you ground from a 220V panel in a bus?

Converting a heavy-duty camper into a bus/coach/truck

Gasmobil · 2007-03-14 · Message 2586 of 3214

Wow!!! Your question is pretty vague... Could you give us a few more details? Like, where, when, and how??? Are you thinking of using a generator, a converter, plugged into a 220V outlet at a house or campsite??

Thanks in advance!!

Best regards.

Converting a heavy-duty camper into a bus/coach/truck

Fr159 · 2007-03-14 · Message 2587 of 3214

Hi Mrkonn

Yes, you can run your circuit on 220V with a grounded outlet, but if your question is whether you can or must connect the bus body to ground, the answer is NO!!!!!!!!!!!!!!

Could you clarify your question, please?

Converting a heavy-duty camper van from a bus/coach/truck

Fr159 · 2007-03-14 · Message 2588 of 3214

hey Gasmobil, you beat me to it, let's hope they don't delete our messages today.... lol

Converting a heavy-duty camper van from a bus/coach/truck

Franois · 2007-03-14 · Message 2589 of 3214

Good evening, I assume you’ve either got a generator or an inverter, both of which should have a grounding terminal. All you need to do is connect to that terminal up to your panel, then attach all your ground wires to the panel’s terminal (the chassis should also be grounded through the inverter or generator, as well as through the appliances mounted on the chassis). But in any case, install a ground-fault circuit breaker in your panel—it’s probably mandatory, though I’m not familiar with your local regulations. Safety first!

Cheers and have a great evening.

PS: I checked out your blog—it’s coming along nicely, keep it up!!!

Converting a heavy-duty camper van from a bus/coach/truck

Franois · 2007-03-14 · Message 2590 of 3214

I see we disagree—I hadn’t seen your reply because I was in the middle of responding. I don’t understand why NOT; it might be difficult to insulate all the devices attached to the chassis or body (metal, of course), but maybe check your regulations?

Converting a heavy-duty camper into a bus/coach/truck

Tom22 · 2007-03-14 · Message 2591 of 3214

hi which companies specialize in converting buses? thanks

Converting a heavy-duty camper van into a bus/coach/truck

Kersode · 2007-03-14 · Message 2592 of 3214

hi there, just a quick heads-up for tomorrow – my schedule’s changed a bit. I won’t be available all day except from 3 to 5 PM. If anything unexpected comes up, I’ll send you a message. see you later

Converting a heavy-duty camper van from a bus/coach/truck

Mrkonn · 2007-03-14 · Message 2593 of 3214

😉Thanks for the response,

The bus will be powered by solar panels and a wind turbine.

🤪In 220V, we have 2 poles + ground—where do we connect the ground? 🤪Sockets for thermal devices, then thermal devices—but where?

Converting a heavy-duty camper van into a bus/coach/truck

Mrkonn · 2007-03-14 · Message 2594 of 3214

😉It's the only one I know http://clients.w3line.fr/electron/faq/public/index.cfm?refsociete=iseobus&lang=fr&rubrique=FAQ&affiche=QR&theme=&id=393

😛

Converting a heavy-duty camper van from a bus/coach/truck

Gasmobil · 2007-03-14 · Message 2595 of 3214

Haha, you're in good spirits, lol!!!

Converting a heavy-duty camper van from a bus/coach/truck

GX47 · 2007-03-14 · Message 2596 of 3214

Hi, for the 220v ground, you need to connect it to the chassis.

Converting a heavy-duty camper van from a bus/coach/truck

Patrick26 · 2007-03-15 · Message 2597 of 3214

since the chassis is already used as the 24V ground, I run the earth wire separately. I don’t connect it to the chassis!

On the panel, I group together on a terminal block the earth terminal from the generator, the one from the Studer combi, all the earths from the sockets and equipment, as well as the shore power earth!

I don’t see what more I can do!

Connecting the earth to the bus body would mean, in my opinion, that in case of a problem, I’d have a 220V AC leakage current wandering around the 24V circuit! And I really don’t want that!

The earth connection with the Studer combi or the generator will make them trip immediately in case of a problem! There’s no need to go through the truck body!

And if you’re on shore power, it’s the shore power circuit breaker that will trip—again, grounding the body doesn’t seem essential to me!

I’ll take a closer look at the 56-201 standard, because if there’s something, it must be in that one. Gasmobil and others, do the same, and we’ll compare notes...

PATRICK26

Converting a heavy-duty camper van from a bus/coach/truck

Patrick26 · 2007-03-15 · Message 2598 of 3214

Adding to that:

You really do need to ground the chassis properly! I find that absurd, but oh well...

However, aside from fuses, differentials aren’t mandatory IN THE PROTECTION PANELS!

The standard assumes that:

Campsite terminals are required to have them, as well as generators, and camper vans! That’s also absurd, but oh well!

PATRICK26

Converting a heavy-duty camper van from a bus/coach/truck

Pestiféré · 2007-03-15 · Message 2599 of 3214

Indeed, these regulations are absurd (even dangerous...) since it's essential to separate the different power sources!! (24VDC and 220VAC!!!) Are you sure these regulations apply to the presence of both power sources and not just an alternative power supply?

Converting a heavy-duty motorhome from a bus/coach/truck

Franois · 2007-03-15 · Message 2600 of 3214

I don’t quite agree; Studer recommends not bridging the ground and the negative because if you do, you’re effectively mixing the two circuits (the - of the 24V= and the negative of the 220V, which isn’t recommended). Plus, in the diagram, the grounding is done through the appliance’s casing, so if it’s attached to a metal part, it connects to the chassis!!!

VoyageForum — the largest community of French-speaking travellers.