Back to the discussion

in Thèmes › Voyager en camping-car

Converting a heavy-duty bus/coach/truck into a motorhome (page 146 of 161)

Discussion started by Patrick26 on 2004-06-14

3213 replies

This thread has been translated into English.


Setting up a heavy motorhome in a bus/car/truck

Fr159 · 2007-05-02 · Message 2901 of 3214

Oh boy I'd be really surprised if the DRIRE would let you get a PTRA when the red section says 'None'. In my opinion, you're stuck...😠

Fitting out a heavy motorhome in a truck/bus/coach

Legx47 · 2007-05-03 · Message 2902 of 3214

Hi everyone, I'm looking for a tri-mix fridge—does anyone know of good places to get one for the best price? Or even a website with more technical information about this type of device so I could maybe repair mine? Thanks in advance

Converting a Bus/Car/Truck into a Heavy-Duty Campervan

Gasmobil · 2007-05-03 · Message 2903 of 3214

Hi. I agree with fr159.

It looks like a tough spot for you with the DRIRE.

Regards.

Outfitting a heavy motorhome in a bus/car/truck

Patrick26 · 2007-05-03 · Message 2904 of 3214

You need to contact the manufacturer!

It's possible you could add a PTRA to your PTAC by modifying the rear axle or by having a brand garage make the modifications so your vehicle matches a different RTI than the one you have!....

Complicated but doable on certain models.

Check with a dealer of the brand. ... and prepare your savings, because the modification will necessarily have to be done by an agent of the brand because it affects the vehicle's structure!

PATRICK26

Setting up a motorhome on a bus/coach/truck

Jerry34 · 2007-05-03 · Message 2905 of 3214

🙂 Hi Patrick26,

There's already a cross-member at the rear of my coach where the towing ring is attached, and it's fixed to the two chassis beams. Don't you think that this original setup would be sufficient to install a hitch to tow a car trailer (approx. 2,000kg)? I might be asking silly questions, but in my view the only stupid questions are the ones that don't get asked.

See you! 😉

Setting up a heavy-duty motorhome in a bus/car/truck

GX47 · 2007-05-04 · Message 2906 of 3214

Hi, for a 608 commercial vehicle with no towing capacity, I asked Mercedes commercial vehicles to give me the same towing capacity as the standard 608 models (specifying that I would register it as a commercial vehicle and would only tow a 1500kg trailer at the time), knowing there was apparently no modification needed other than adding a towing ball and electrical socket, Mercedes commercial vehicles, after checking compatibility (based on the serial number), told me OK, you need to go through our workshops, that will cost you 12,000 F (in 1999) because they needed to check the brake power.

Strangely, in 2000, they asked me for the same amount at Mercedes passenger vehicles for a complete towing kit for a 300 TD (I had one installed for 800 F at a competitor) 😉

In summary, the towing capacity must have already existed on the vehicle in question (due to first-registration requirements) otherwise it's a flat no (example: Heuliez buses on Iveco chassis—impossible to get towing capacity) Moreover, it's not the regulatory authority that can add towing capacity, only the manufacturer. And for towing equipment on a commercial vehicle, you need to go through a coachbuilder who will certify the towing kit. The junkyards around here refuse to sell used towing kits or used towing balls (my GX47 could tow 3.5T, but I never managed to find a used towing ball for it).

Setting up a motorhome in a commercial vehicle

Patrick26 · 2007-05-04 · Message 2907 of 3214

FYI GX47, I'm in a similar situation with my DAF.

I have the RTI showing 3500 kg with trailer brakes 7000 kg with air brakes,

and no cross-bar!

After checking with DAF, all chassis in the 2100 series (mine included) were delivered like that, and DAF doesn't make a tow bar for this chassis!

So what do I do then?

Their answer was simple:

Like everyone else! Since it's already in your RTI, go right ahead and do it! And if you want it at chassis height, fit a cross-bar between the two side rails, and if you want a passenger-car tow ball, you mount a plate directly under the bumper with braces from the holes in the chassis cross-members. That's how it's designed. All our customers have done it this way, and no inspector has ever questioned whether the coupling was fitted before or after the red line!

So I'm going to do it! No other choice!

As for braking, if the trailer is properly set up, no problem...

PATRICK26

Setting up a heavy motorhome in a bus/van/truck

Papavoyage · 2007-05-05 · Message 2908 of 3214

Hey, your advice is really valuable! Thanks. I'm about to insulate my Master T 35 following your tips. I just want to know what type of adhesive to use to attach it to the bodywork. I bought 7-layer insulation and I'm hoping that's enough for moderate summer/winter use—no extreme temperatures. Thanks in advance for the glue recommendation! BYE

Converting a bus/van/truck into a motorhome

Patrick26 · 2007-05-05 · Message 2909 of 3214

Get an MS polymer resin-based adhesive sealant. You'll find affordable ones in pump cartridges at hardware stores. For your fingers, it cleans up with white spirit!

The advantage over neoprene is that you only apply it on one side, and it's compatible with everything (plastic included!)

PATRICK26

Setting up a heavy motorhome in a bus, truck, or camper

Papavoyage · 2007-05-06 · Message 2910 of 3214

Hi Patrick 26, and thanks for the advice. I have one more question: I've got a big hole in the bodywork I need to patch, and I want to weld a piece of sheet metal using arc welding (that's all the equipment I have). A neighbor told me to disconnect the battery to avoid frying it, but won't I risk frying the alternator and the starter anyway when I'm using the bodywork as part of the welding circuit? I hope you have the answer. Thanks BYE

Outfitting a heavy-duty motorhome in a bus/coach/truck

Patrick26 · 2007-05-06 · Message 2911 of 3214

Disconnect the 2 battery terminals and make sure your chassis is properly supported on its tires and that there's no scrap metal bar creating a ground connection with the chassis and everything will be fine. But the best way to fill a hole is with oxy-acetylene and filler metal! There you risk doing more harm than good. Be careful!

Check out my blog—with oxy-acetylene we re-welded a torn metal panel over 30 cm, perfect! Arc welding could never have done that!

PATRICK26

Converting a truck into a motorhome for horses

Apsaratosca · 2007-05-06 · Message 2912 of 3214

Hi, So here's the thing – I'm passionate about horses and own a mare. I'm looking to buy a light-duty truck (I don't have a heavy-duty license!) and convert it for two horses with a small bunk bed and sink area so I can travel comfortably without having to pay for a hotel room each time.

Can I do the conversion myself, or is that prohibited? Do I need to have it inspected? Is there a risk it won't pass? What do they check? How much does the inspection cost?

Thanks for your help!

Converting a heavy-duty camper into a bus/coach/truck

Papavoyage · 2007-05-06 · Message 2913 of 3214

Thanks for the advice. I tried arc welding: help!!! I’m burning through the bodywork. On top of that, after removing the wooden floor and clearing out the rusty corners, I found some serious holes—15 cm by 15 cm. I’ll check if you left any tips for filling them with fiberglass. Thanks for the replies and the great tips. Oh, and I don’t have any other way to weld. Bye

Converting a heavy-duty bus/coach/truck into a camper

CarHibou · 2007-05-07 · Message 2914 of 3214

Hi!

Just wanted to share this: http://donnons.org/annonce.php?idAnnonce=1419

It's a bus being given away (so up for grabs!)... the guy gave me a bit more info: " It's a vehicle equipped as a 9-bed dormitory with water and sanitary installations. Needs some work. It hasn't been driven for at least 4 years and requires a safety inspection, although these were checked 4 years ago. The engine was changed at 2000 km, the tires are new. Originally given to an association, they had no use for it at all. It's parked in a hangar, so it's protected. Registration as a vintage vehicle means it can't transport passengers except one plus the driver and requires a logbook if it travels beyond the neighboring departments of its registration. Still available at this time. Year: 1964. It's ready to be painted. It's registered. "

On the other hand, it's a bit of a poisoned gift, since as a vintage vehicle, you'd need to get it through a VASP inspection! (Gasp! ;) ) Still, at worst, there are some parts you could salvage! ;)

You've been warned! :)

Converting a heavy-duty bus/car/van into a motorhome

Piét4N · 2007-05-07 · Message 2915 of 3214

Hi!

Your post is a bit off-topic, still!... But since we're not brutes, I’ll answer anyway. Of course you can customize your truck yourself. And of course it needs to go through the *Mines* inspection, given the modifications you want to make. And of course there’s a risk it won’t pass! To get it approved, you must comply with the current standards for this type of vehicle (the *Mines* will tell you the exact category based on your planned conversion). And here’s WHAT YOU NEED TO DO: buy the AFNOR standards manual for these vehicles, available at any bookstore. This book covers all the requirements. A *Mines* inspection costs around 90 €, plus the technical inspection, plus weighing (for heavy vehicles—no idea for light ones). By the way, do you know the forum http://merco.aceboard.fr? I’m sure you’ll find tons of answers there!

Piéton

Converting a heavy-duty camper van from a bus/coach/truck

Fr159 · 2007-05-07 · Message 2916 of 3214

Hi everyone,

I’m not sure if the AFNOR guide is in every bookstore🙂, but that’s the one you need.

Here are the current prices in my department (59): - Veritas 56200 standard check: 252.36 € - Speed limiter: 71.45 € * - Technical inspection: 84.06 € - DRIRE: 86.90 €

All these prices include tax.

* In VASP, we’re actually not required to insert a disk into the tachograph, so we no longer have to get it inspected. However, I found out that the annual inspection of the speed limiter is mandatory!! Does anyone have any tips on how to avoid it?

Converting a heavy motorhome in a bus/coach/truck

Jerry59 · 2007-05-07 · Message 2917 of 3214

Hi,

I'd like to know if the AFNOR guide sold on this link is the right book?

I'm from Lille and I'm planning to start my motorhome project in an FR1 as well, probably starting this summer.

Thanks for the answer.

AFNOR Guide: http://www.boutique.afnor.org/LIV7DetailLivre.aspx?&nivCtx=LIVZLIVZ1A10A201A206&ts=1866132&CLE_ART=FA092059

Setting up a motorhome in a heavy-duty bus/coach/truck

Piét4N · 2007-05-08 · Message 2918 of 3214

Hey everyone!

Yes, that link leads to the right book, that's the one you need if you're aiming for the MotorHome category.

FR159: it's true that not all bookstores have it in stock, but it's also true that you can order it from any bookstore...

I'd like to get back to the discussion about the electrical system: should you ground the metal chassis of the bus or not? To the neutral of the 220V? To the negative of the 24V? Does it depend on the situation: presence of a converter, a heating unit, a charger...? If the standard, as written, is dangerous, how do you justify doing it differently? Mr Carriage RV, as a professional, what's your take on this?

Piéton

Outfitting a Heavy Motorhome in a Bus/Coach/Truck

Fr159 · 2007-05-08 · Message 2919 of 3214

Hey

Like Piéton told you, "yes" that's the one. Since you're from Lille, you can go get it directly from AFNOR which is just nearby in Marcq en Bareul. If you want, you can come check out mine, I'm 50 km from Lille

Catch you

Setting up a large motorhome in a bus/coach/truck

Fr159 · 2007-05-08 · Message 2920 of 3214

I'm not going to argue about what some people (myself included) think is dangerous or stupid, with or without a generator—I'm going to stick to what the regulations say. The 24 volt DC ground is and must be connected to the ground (it's done that way as standard). The 220 volt earth (not the neutral) must be connected to the ground.

Under these conditions, apart from using a generator, it's safe for the users—much less so for the equipment . On reflection.. the first one's still more important... no?

VoyageForum — the largest community of French-speaking travellers.